Team:UCL/Science/Proto

Materials
LB Media, 50ml Falcon Tubes, Ice, Chilled centrifuge, Calcium Chloride (CaCl2), Eppendorf tubes (300ul/tube)

Procedure
1. Inoculate a single colony into 5ml Lb in 50ml falcon tube. Grown O/N @ 37oC
2. Use 1ml to inoculate 100ml of LB in 250ml bottle the next morning.
Shake @ 37oC for 1.5-3 hours.

Or

1. Inoculate a single colony into 25ml LB in a 250ml bottle in the morning
2. Shake @ 37oC for 4-6 hours.

Then…

3. Put the cells on ice for 10mins (keep cold from now on).
4. Collect the cells by centrifugation in the big centrifuge for 3 minutes @ 6Krpm.
5. Decant supernatant and gently resuspend on 10ml cold 0.1M CaCl (cells sensitive to mechanical disruption).
6. Incubate on ice x 20 minutes
7. Centrifuge as in 2.
8. Discard supernatant and gently resuspend on 5ml cold 0.1M CaCl/15%Glycerol.
9. Dispense in microtubes (300ųl/tube). Freeze at -80oC.
Note: Home-made competent cells were used to transform registry BioBricks

Materials
MilliQ water, NEBuffer 2.1, BSA, Pipettes and autoclaved tips Enzymes: EcoRI-HF, SpeI, XbaI and PstI,

Notes

The volume of DNA to be digested will depend on the concentration obtained from miniprep of the DNA from culture. This must be made up to 500ng for each 50ul digestion
eg. if concentration BBa_R0010 is available at a concentration of 330ng/ul
we require 500/330 = 1.5ul of the DNA solution for a digestion

All digestions carried out for iGEM purposes i.e. BioBrick creation are double digests. NEBuffer 2.1 is the ideal buffer for all combinations used.

Depending on whether the part being digested is an upstream insert, downstream insert or plasmid backbone, the combinations of enzymes differ.
For Upstream parts, such as promoters digest with EcoRI-HF and SpeI
Digest downstream parts with XbaI and PstI
Digest plasmid backbones with EcoRI-HF and PstI

Procedure
1. Calculate amount of DNA solution that will be needed for 500ng
2. Following this, calculate the amount of water needed to make up to 50ul if both enzymes and BSA are 1ul each and Buffer is 5ul.
3. Add the components to a microcentrifuge tube in the order: Water > Buffer > BSA > DNA > Enzymes
4. Leave to incubate at 37ºC for 1-2 hours
5. Remove and deactivate the enzymes by incubating at 80ºC for 20 minutes

Materials
LB Agar powder, plates, antibiotics, sterile jar, sterile flame or biosafety cabinet.

Procedure
1. Dissolve LB agar in sterile/autoclaved jar of sterile water 40g/L.
2. Swirl until completely dissolved
3. Autoclave LB agar

The following steps should be completed under a sterile flame or biosafety cabinet. Ideally after autoclaving, before LB Agar solidifies:

4. Add antibiotics from their stock solutions in 1:1000 ratio with LB agar, can be added either directly to each individual plate or to the entire solution.
5. Pour agar into plates, roughly half way (30-50mL per plate). Leave plates with lids half on (prevent condensation).
6. Allow plates to solidify under flame
7. Cover and leave on bench or in fridge

Materials
Competent Cells, Plasmid DNA, Antibiotic Plates

Procedure
1. Thaw competent cells on ice
2. 50uL cells enough for 1 transformation
3. Add 1ug of DNA to 50uL competent cells

If biobrick from distribution, resuspend DNA well in 10uL ddH20

4. Add 2-5uL DNA i.e. ligation product or BioBrick re-suspension to 50uL competent cells
5. Flick by hand or pipette up and down gently
6. Place cells on ice for 30 minutes
7. Place cells in water bath or heat block at 42oC for 30 seconds
8. Place cells on ice for 2 minutes
9. Add 950ul of SOC or LB media and place in a shaking incubator for a maximum of 2 hours (37oC/250rpm) 10. Label two petri dishes with LB agar and the appropriate antibiotics(s) with the date, plasmid backbone and ligated genes/parts and antibiotic added.
You may also choose to write down the volume of transformed product plated
11. Spin down the incubated cells for 2mins at 4000rpm to obtain a cell pellet.
12. Pipette 100ul of the supernatant or fresh LB media before discarding the rest of the supernatant and re-suspending the pellet in the 100ul of media
13. Incubate the plates at 37ºC for 12-14 hours, always place plates lid-down.

If incubated for too long the antibiotics start to break down and un-transformed cells will begin to grow. This is especially true for ampicillin - because the resistance enzyme is excreted by the bacteria, and inactivates the antibiotic outside of the bacteria

You can pick a single colony, make a glycerol stock, grow up a cell culture and miniprep.

Count the colonies on the 20 μl control plate and calculate your competent cell efficiency.

Prepare Agarose Gel (1%) for Electrphoresis
Materials:
Agarose powder, spatula, weighing boat, microwave, Ethidium Bromide, Gel dock,

1. Add ingredients to flask and microwave for about 120 seconds. Shake. Repeat until mixture fully dissolved.
2. Leave to cool for 20-30 seconds.
3. Add 20ul of Ethidium Bromide.
Place comb in gel frame. When flask is cool enough to handle, pour the solution into the gel frame and leave to set (10-20 minutes).

Preparing for Loading:

1. Prepare Ladder

• a. Add 1ul of DNA ladder to labelled Eppendorf.
• b. Add 1ul of DNA loading buffer (dye) to Eppendorfs containing DNA and DNA ladder (Unless ladder is already combined with dye).
• c. Add 1ul of milliQwater.
• d. Spin down

2. Prepare Samples:

• a. Add 10ul of digest (250ng of DNA) to 3ul of loading buffer.

Loading the gels
1. Place gel frame in electrophoresis box with black (cathode) part away from you and red (anode) part closest to you.
2. Carefully remove comb from gel.
3. Fill the top and bottom wells with 1x TAE. Pour over top of gel, continue pouring until gel is covered.
4. Load the wells starting with the DNA ladder in lane 1. Be sure to note which lane each sample is loaded into.
5. Run gel for approximately 60 minutes at constant voltage of 120V. Check for bubbles at the cathode which shows it has started.