Team:CSU Fort Collins/Notebook/Protocols=Miniprep
From 2014.igem.org
(Difference between revisions)
Line 724: | Line 724: | ||
<div class='page'> | <div class='page'> | ||
<p> | <p> | ||
- | |||
Before starting: | Before starting: | ||
<ul> | <ul> | ||
<li>Add RNase A to Resuspension Buffer (R3) according to the instructions on the label; mix well</li> | <li>Add RNase A to Resuspension Buffer (R3) according to the instructions on the label; mix well</li> | ||
- | <li>Mark on the label that RNase A is added. Store Buffer R3 with RNase A at 4 | + | <li>Mark on the label that RNase A is added. Store Buffer R3 with RNase A at 4 °C</li> |
- | <li>Warm Lysis Buffer (L7) briefly at 37 | + | <li>Warm Lysis Buffer (L7) briefly at 37 °C to redissolve any particulate matter</li> |
<li>Add 100% ethanol to Wash Buffer (W9) and Wash Buffer (W10) according to the instructions on each label; mix well</li> | <li>Add 100% ethanol to Wash Buffer (W9) and Wash Buffer (W10) according to the instructions on each label; mix well</li> | ||
<li>Store wash buffers with ethanol at room temperature</li> | <li>Store wash buffers with ethanol at room temperature</li> | ||
Line 789: | Line 788: | ||
<li>The recovery tube now contains the purified plasmid DNA</li> | <li>The recovery tube now contains the purified plasmid DNA</li> | ||
<li>Discard the column</li> | <li>Discard the column</li> | ||
- | <li>Store plasmid DNA at 4 | + | <li>Store plasmid DNA at 4 °C (short-term) or store the DNA in aliquots at -20 °C (long-term)</li> |
</ul> | </ul> | ||
</ol> | </ol> |
Revision as of 17:49, 9 October 2014
Plasmid Miniprep Protocol
Show Table of Contents
Before starting:
- Add RNase A to Resuspension Buffer (R3) according to the instructions on the label; mix well
- Mark on the label that RNase A is added. Store Buffer R3 with RNase A at 4 °C
- Warm Lysis Buffer (L7) briefly at 37 °C to redissolve any particulate matter
- Add 100% ethanol to Wash Buffer (W9) and Wash Buffer (W10) according to the instructions on each label; mix well
- Store wash buffers with ethanol at room temperature
- Harvest
- Sediment the cells by centrifuging 1 - 5 mL of the overnight LB culture (use 1-2 x 109 E.coli cells for each sample)
- Remove all medium
- Resuspend
- Add 250 μL Resuspension Buffer (R3) with RNase A to the cell pellet
- Resuspend pellet until it is homogeneous
- Lyse Note: This step is time sensitive.
- Add 250 μL Lysis Buffer (L7)
- Mix gently by inverting the capped tube five times (Do NOT vortex)
- Incubate the tube at room temperature for 5 minutes
- Precipitate
- Add 350 μL Precipitation Buffer (N4)
- Mix immediately by inverting the tube, or for large pellets, vigorously shaking the tube, until the mixture is homogeneous (Do NOT vortex)
- Centrifuge the lysate at >12,000 X g for 10 minutes
- Bind
- Load the supernatant from step 4 onto a spin column in a 2-mL wash tube
- Centrifuge the column at 12,000 X g for 1 minute
- Discard the flow-through and place the column back in the wash tube
- Wash and Ethanol Removal
- Add 700 μL Wash Buffer (W9) with ethanol to the column
- Centrifuge the column at 12,000 X g for 1 minute
- Discard the flow-through and place the column back into the wash tube
- Centrifuge the column at 12,000 X g for 1 minute
- Discard the was htube with the flow-through
- Elute
- Place the spin column in a clean 1.5-mL recovery tube
- Add 75 μL of preheated TE Buffer (TE) to the center of the column
- Incubate the column for 1 minute at room temperature
- Recover
- Centrifuge the column at 12,000 X g for 2 minutes
- The recovery tube now contains the purified plasmid DNA
- Discard the column
- Store plasmid DNA at 4 °C (short-term) or store the DNA in aliquots at -20 °C (long-term)