Digestion

Dephosphorylation of plasmid

Ligation

PCR

We used different polymerases for different usage during the project.

1. To make constructs and amplify plasmid backbones we used the high efficient, exonuclease active Q5® High-Fidelity DNA Polymerase (NEB). We followed protocol supplied by the enzyme and used a 50µl Reaction volume and 50 ng DNA.

   PCR Setup:

   1. 98degrees, 30 sec
   2. 98 degrees, 10 sec
   3. 55 degrees, 30 sec
   4. 72 degrees, 2 min (go to step 2, 28 times)
   5. 72 degrees, 2 min
   6. 8 degrees, hold

2. To check if colonies contain our construct we used TaKaRa ExTaqTM Hot start Version.

   One bacteria colony were re-suspended in 20ul dH2O

   The sample was put on 95-100 degrees in 10 minutes to break the bacteria and free the plasmid into the solution

   The sample was centrifuged at full speed for 2 min. The plasmid is then in the supernatant.

   We used 2ul of this supernatant in the PCR reaction.

   We followed protocol supplied by the enzyme and used a 50 µl Reaction volume

   PCR Setup:

   1. 98 degrees, 1 min
   2. 98 degrees, 10 sec
   3. 55 degrees, 30 sec
   4. 72 degrees, 3,5 min (go to step 2, 30 times)
   5. 72 degrees, 5 min
   6. 8 degrees, hold

PCR clean up

Followed protocol supplied with the kit. Eluted DNA in 20µl ddH2O

Making of N-His tag

We made our own seven histidin long N-terminal his tag by ordering complementary oligos and anneal them to each other.

The two oligoes were mixed and heated up to 95degrees. The temperature was then slowly decreased to find the correct annealing temperature for the oligoes. The temperature was decreased until 50 degrees over a 5-8h period. This was done in a PCR machine or in a water bath.

The concentration of oligos was: 20uM.

Digestion (NEB restriction enzymes)

We used 500ng DNA in a 25 µl digestion volume. 2,5 µl buffer (supplied with the enzyme), 0,5µl Enzyme and water up to a total amount of 25µl. Digested in 37 degrees for 1-2h.

Ligation (T4 – NEB ligase)

We used 50ng Plasmid (2 µl), equimolar amount if construct, 2µl buffer (10X), 1µ T4 ligase and water up to a total volume of 20µ. Ligated at Room Temperature for 30min – 1h.

3A assembly – iGEM protocol

Part A: digested with EcoRI and SpeI

Part B: digested with PstI and XbaI

Plasmid backbone: digested with EcoRI, PstI and DpnI

Equimolar of each part where ligated together

Assembly into pSB1C3

Part: Digested with EcoRI and PstI

Plasmid backbone: Digested with EcoRI, PstI and DpnI

Equimolar of each part were ligated together

Transformation of E.Coli TOP10

1. Add 2ul DNA /Ligated product (ca 50ng) to 50ul bacteria
2. On ice for 30 min
3. Heat shock: 40 sec in 42 degrees
4. On ice for 2 min
5. Add 350ul SOC medium
6. On shake at 37degrees for 1h (step 5 +6 is not necessary for bacteria containing ampicillin resistance)
7. Centrifuge at top speed for 2 min
8. Remove supernatant and re-suspend bacteria pellet in 30-75ul of medium
9. Plate bacteria on plates with correct antibiotics

Miniprep

Followed protocol supplied with the kit. Eluted DNA in 50µl ddH2O

Chemically Competent TOP10 E.coli cells

1. 5ml O/N culture of bacteria diluted in 1:100 in fresh LB.
2. Grow at 37 degrees to mid-log phase. OD= 0.3-0.5.
3. Centrifuge at 10min for 4000 rpm
4. Resuspend in ¼ of original volume of ice cold 0.1M Cacl2.
5. Incubate on ice for minimum 30 min
6. Pellet the cells. Resuspend in 1/25 of original volume in ice cold 0.1M CaCl2
7. Add equal volume of ice cold 60% glycerol – mix well
8. make aliquots of the cells and store them at -80 degrees.

Cells were tested by the iGEM competent cell.

TBE buffer (10X sample)

• 10,8g Tris Base
• 5,5g Borat
• 0,7g EDTA-Na2
• 1 litre of dH2O

Gel loading buffer

• 250mg Bromphenol blue
• 250mg xylene cyanol
• 3ml Glycerol
• dH2O to a total volume of 10ml

Gel electrophoresis

Gels were run on 100V for 20-30 minutes.

We used White light to visualize the DNA stained with mindori green.

Agarose gel

We have used 0,8% agarose gels.

50ml 1X TAE buffer in 0,4g agarose.

We used Midori green DNA stain to visualize the DNA in the gel

Growing bacteria from Freeze stock

Take the bacteria out from the -80 Freezer.

Use the sterile bench and pins to plate out bacteria directly on agar with correct antibiotics

DNA concentration

We have been using NanoDrop to measure DNA concentrations.

LB-Agar Plates and LB medium

We followed recommended concentrations of antibiotics on the LB-Agar plates and medium (100 μg/mL).

We have used Ampicillin, Chloramphenicol, and Kanamycin.

SOC Medium

• Add: LB Medium
• 10mM MgSO4
• 2% Glucose
• Filtrate the sample

Sequencing

We used GATC sequencing facilities.

5µl DNA (consentration of 80-100ng/µl) and 5µl 5mM primer added to an Eppendorf tube.

We used VF and VR2 primers for sequencing.