Stability

Our subteam aims to test the stability of ten different Biobricks transformed in two different strains of Escherichia coli, XL1 Blue and DH5α . Stability is determined by subjecting the transformed cells to different types of stress and comparing the output with non-transformed ones grown in the same conditions, as well as with cells transformed with an empty plasmid (without Biobrick).

Temperature Stress

We start out by establishing an overnight culture of each strain, every one of which will be subjected to the different temperatures. The experiment will be carried out in an improvised miniature system we just developed; PCR tubes filled with 75 µL of culture are placed in a thermo cycler, in which a gradient of temperatures from 30-50ºC will be set. In each round, four replicas of two strains are to be tested simultaneously at 12 different temperatures:

four replicas of two strains tested simultaneously at 12 different temperatures

After an incubation period at the given temperatures the tubes containing the culture will be collected to measure the O.D. Fluorescence will also be measured and later normalized to O.D.₆₀₀, to compare the expression of the different Biobricks.

Material Fatigue

The idea is analogous to material fatigue in material sciences; in materials science, fatigue is the weakening of a material caused by repeatedly applied loads. If the loads are above a certain threshold, microscopic cracks will begin to form at the stress concentrators such as the surface, persistent slip bands and grain interfaces. In our case, we chose to induce the fatigue by subjecting the cells to temperature fluctuation, every minute the temperature will be changed from 37ºC (E.coli optimum growth temperature) to 41ºC and back to 37ºC again, this way, the temperature oscillates every minute from 37 to 41ºC for 4 hours. What will be the effect of such thermal fluctuations?

pH & Salinity

One of the best known factors that conditions bacterial growth is proton and salt concentration in the media. This experiment, as simple as may seem, offers the opportunity to test cell viability as well as the Biobrick behaviour at different pH and salt concentrations. Overnight cultures of both strains will be resuspended in different LB media with pH ranging from 5 to 9 and incubated for 90 minutes, after which O.D.₆₀₀ and fluorescence of each tube is to be measured. The design of the experiment is the same for salts, ranging from LB medium without salt to an extra 4% of salt, maintaining the normal pH of the LB medium for all the tubes.

UV Radiation

As per today, high doses of UV light are proven detrimental to life, but, to what extent is it injurious to an E.coli cell? Is transformation a factor that enhances the lethality of UV radiation or, contrary to what logic dictates, helps resist the UV radiation? Curiosity led us to design an experiment which would answer these questions: overnight cultures of the strains will be diluted and spot-plated on LB agar. Subsequently, the spots will be subjected to timed pulses of UV radiation (intensity of 340 µW/cm²⁾ with a control that receives no UV irradiation at all. Thereafter the plates will be incubated and fluorescence will be measured and normalized to O.D._600.

Vacuum

A simple experiment which mainly consists of exposing the cells, spot-plated on Petri dishes, to vacuum during 48 hours will be carried out; the output from these, as always, compared to cells spot-plated and grown in optimal conditions, through OD₆₀₀ and fluorescence assays.

Standardization

One should not assume that a functional module working fine in one cell type will work the same way in even a closely related cell type (Renshaw, 1993). Whereas traditional engineering practices typically rely on the standardization of parts, the uncertain and intricate nature of biology makes standardization in the synthetic biology field difficult. Beyond typical circuit design issues, synthetic biologists must also account for cell death, crosstalk, mutations, intracellular and extracellular conditions, noise and other biological phenomena. As the number of system components grows, it becomes increasingly difficult to coordinate component inputs and outputs to produce the overall desired behaviour (Purnick & Weiss, 2009). In the ST²OOL Project, we wanted to check how standard biobricks are. For this goal, we are using a set of strains of Escherichia coli transformed, in single transformation, with ten different Biobricks whose outputs will be measured by fluorometry, colorimetry or luminometry. The aim of this approach is simple and fits with the answer to the following question:

Will the Biobricks behave the same way independently of the host strain they have been transformed into? Will we obtain the same output from all of them? The answer to these questions… in two months!

References

Purnick, P. E. M. & Weiss, R. The second wave of synthetic biology: from modules to systems. Nature Reviews 10, 410-422 (2009).

Purnick, P. E. M. & Weiss, R. Renshaw, E. Modelling Biological Populations in Space and Time. Cambridge University Press (1993)10, 410-422 (2009).

Green

green green green green green

Blue

blue blue blue blue blue