Team:Aachen/Notebook/Engineering/WatsOn

From 2014.igem.org

Revision as of 06:38, 15 October 2014 by Bpeeters (Talk | contribs)

Software


Build your own WatsOn

If you want to create your own WatsOn at first check the following list of necessary devices.

Table 1: Needed number of pieces, components and costs for building your own measurement device

number of pieces components costs [$]
1 [http://www.prolighting.de/Zubehoer/Farbfilter/Lee-Filter_HT/Lee-Filters_Musterheft_Designer_Edition_i174_3965_0.htm filter slides] (medium yellow 010, sally green 505)5.17
1 [http://www.dx.com/p/uno-r3-development-board-microcontroller-mega328p-atmega16u2-compat-for-arduino-blue-black-215600 arduino UNO R3]11.65
1 [http://www.dx.com/p/arduino-2-channel-relay-shield-module-red-144140 2-channel relay shield]3.46
40jumper-wire cable2.99
1 [http://www.dx.com/p/2-54mm-1x40-pin-breakaway-straight-male-header-10-piece-pack-144191 40er male header (10-Piece Pack)]2.72
1 [http://www.dx.com/p/jtron-2-54mm-40-pin-single-row-seat-single-row-female-header-black-10-pcs-278953 40er female header (10-Piece Pack)]2.60
1 [http://www.dx.com/p/prototype-universal-printed-circuit-board-breadboard-brown-5-piece-pack-130926 circuit board]2.99
1 [http://www.newark.com/pro-signal/rp006/audio-video-cable-hdmi-1m-black/dp/96T7446 HDMI cable]1.87
1 [http://www.dx.com/p/hd-053-high-speed-usb-2-0-7-port-hub-black-174817 7 port USB hub]6.71
1[http://www.dx.com/p/dx-original-ultra-mini-usb-2-0-802-11n-b-g-150mbps-wi-fi-wlan-wireless-network-adapter-black-252716 WLAN USB stick]5.35
1USB mouse and keyboard12.50
1 [http://corporate.evonik.com/en/products/pages/default.aspx case acrylic glass XT 6mm~0.52]50.65
1spray paint for acrylic glass6.54
1 [http://www.newark.com/raspberry-pi/raspberry-modb-512m/raspberry-pi-model-b-board/dp/68X0155 Raspberry Pi model B board]35.00
1[http://www.newark.com/raspberry-pi/rpi-camera-board/add-on-brd-camera-module-raspberry/dp/69W0689 Raspberry Pi camera module]25.00
1[http://www.pollin.de/shop/dt/NzUwOTc4OTk-/ 7” display]50.50
1[http://www.dx.com/p/diy8-x-seven-segment-displays-module-for-arduino-595-driver-250813 8-segment display]3.86
2 [http://www.dx.com/p/arduino-dht11-digital-temperature-humidity-sensor-138531 digital temperature sensor DHT-22]7.50
1 aluminum block 100x100x15 mm14.23
1 [http://www.dx.com/p/tec1-12706-semiconductor-thermoelectric-cooler-peltier-white-157283 Peltier heater 12V 60W]4.49
1power supply32.89
6 [http://www.leds.de/Low-Mid-Power-LEDs/SuperFlux-LEDs/Nichia-Superflux-LED-blau-3lm-100-NSPBR70BSS.html superflux LED 480nm]7.50
16LED 450nm7.50
2 Resistor 40 Ohm0.30
4 Resistor 100 Ohm0.60
1cupboard button1.24
-total309.45

You can find more economical information for WatsOn and the project on our Economical View page.

Aachen Device Fritzing.png
Wiring of our device
Aachen Device 1.jpg Start building your own WatsOn by assembling the base plate, the sides and the interior wall.
350px] [File:Aachen_Device_.3jpg Fix the Peltier heater on the back of the aluminum block and place it in the hole of the interior wall.
Arrange the 4x4 450nm LEDs and the 2x3 480nm LEDs
Aachen Device 7.jpg Assemble the camera holder with the camera and the corresponding filter slide on the lower part. Over the camera you can place the temperature sensor for measuring the indoor temperature. Finally put the fan on the back of the camera holder.
Aachen Device 8.jpg Connect the electronic components on the outside and the inside according to the wiring diagramm.
Aachen Device 4.jpg Put together the drawer.
Aachen Device 9.jpg Position the front panel and insert the drawer.
Aachen Device 10.jpg Place the temperature sensor for the aluminium block temperature directly on the block and put the back panel in front of it.
Aachen Device 6.jpg Setup the power supply and connect all devices to either 5V or 12V.
Aachen Device 11.jpg Mount the device on top of the power supply casing. Add the display and apply some stickers to enjoy your custom-made WatsOn.