From 2014.igem.org

(Difference between revisions)

Revision as of 15:20, 28 August 2014

iGEM ETH Zurich 2014

{{{1}}}

Blog

troisieme

deuxieme

premier

cinquieme

sixieme

qutrieme

Diffusion Experiments

Monday, 25th August

Now that we tested the different constructs for leakiness, dose response and cross talk, we are investigating in the diffusion rate of AHL. Therefore we designed a chip with chambers connected by channels of different length (see figure). In one chamber we added a strain containing a regulator and a sensor plasmid, to the second chamber we added AHL or an AHL producer strain. As soon as AHL is diffused to the former chamber it induces sfGFP production on the sensor plasmid. The time it takes until we can measure the sfGFP signal and the length of the channel gives us information about the velocity of AHL diffusion.

PDMS millifluidic chip used for diffusion experiments

Three main experiment designs were tested and modified: the agar-design, the liquid-design and the beads-design.

For the agar-design we filled the chamber and channels with LB-agar or in a second attempt with agarose only. Subsequently, we punched a cylindric hole in each chamber. The capacities were filled with regulator/sensor strain culture or AHL/AHL producer strain culture, respectively. After 3 to 4 h at 37 °C we could observe an increase in the sfGFP signal. Since we used comparably high concentration of AHL in our first attempts, we could not detect a delayed sfGFP signal for chambers connected by a longer channel. The experiment will be repeated using lower concentrations. However, conducting the experiment using the agar-design, we encountered a problem: after some hours the LB-agar/agarose started to shrink and dried out. Thus, the agar-design cannot be used without modifications for experiments of longer duration.
In an attempt we only left a small agar fragment in each channel and filled the rest with liquid medium, so as to decrease chance of it drying out, while avoiding at the same time that bacteria from one chamber reach the other chamber.
The bead-design consists of an alginate bead for each chamber and liquid medium in between. The beads either contained regulator/sensor-bacteria or AHL.

Diffusion experiment with agar. Click here to watch the video.

Diffusion experiment with liquid. Click here to watch the video.

Diffusion experiment with beads. Click here to watch the video.

Week 14 : Diffusion experiments started, simulated with Comsol, and fitting of quorum sensing dynamics

Monday, August 25th

We carried diffusion experiment with different designs : punched PDMS, liquid, beads. For every design we added high concentrations of pure AHL in the sender well, so cells are glowing a lot. However because of this high concentration, diffusion is very high and at a given AHL concentration, receiving cells are glowing at the same time for all 4 channel lengths. Check the corresponding article for more details.

We have a Comsol simulation for these experiments that explains why at this concentration of AHL (1mM), all 4 wells glow at the same time irrespectively of channel length. Check this article for more details.

We could fit degradation rates of external, internal AHL and GFP thanks to quorum sensing dynamic curves.

Check the corresponding article for more details.

Week 13 : Steady state quorum sensing fitted and human practice survey launched !

Wednesday, August 20th

Our first diffusion try with highlighter ink !

Camera picture of our punched agar chip glowing highlighter ink

The design of punched agar doesn't seem to be the best but at least we can see something. Diffusion experiments with different designs are running now.

We have been fitting quorum sensing experiments at steady state to a Hill function and found some quorum sensing parameters.

Fitting quorum sensing Hill function parameters thanks to steady-state data from experiments. Check the corresponding article for more details.

We wrote a survey in English, in French and in German on complexity for our human practice project. We expect 500 responses.

Construction of the regulator plasmids

Thursday, July 5th

Construction of the lasR regulator plasmid (piG0040)

Competent cells were transformed with piG0028 (K553003, lasR) and selected on chloramphenicol-LB-plates. Plasmid DNA was extracted by performing a miniprep. The relevant plasmid sequence was sequenced by Microsynth using the primers oiG0001 and oiG0002. Amplification of lasR by PCR using oiG0003 and oiG0004 resulted in the fragment fiG0004 (1.0 kb). The vector piG0034 (pSEVA 181) was digested with the restriction enzymes HindIII and PacI to fiG0001 (3.0 kb). The two fragments, fiG0001 and fiG0004, were assembled using Gibbson assembly. Thus we used the plasmid backbone of piG0034 and lasR of piG0028 to construct the lasR regulator plasmid piG0040. Competent cells were transformed with piG0040 and selected on ampicillin-LB-plates. Colony PCR using the primers oiG0035 and oiG0036 was conducted to check the size of the inserted fragment (expected bands at 1.0 and 1.2 kb). The sequence was verified by Microsynth using the same primers.

Construction of the luxR regulator plasmid (piG0041)

Competent cells were transformed with piG0008 (F2620, luxR) and selected on chloramphenicol-LB-plates. Plasmid DNA was extracted by performing a miniprep. The relevant plasmid sequence was sequenced by Microsynth using the primers oiG0001 and oiG0002. Amplification of luxR by PCR using oiG0005 and oiG0006 resulted in the fragment fiG0005 (0.8 kb). The backbone of the vector piG0040 (lasR in pSEVA 181) was amplified by PCR using oiG0007 and oiG0008. This fragment, fiG0011 (3.2 kb), and fiG0005 were assembled using Gibbson assembly. Thus we formally replaced lasR by luxR to construct the luxR regulator plasmid piG0041. Competent cells were transformed with piG0041 and selected on ampicillin-LB-plates. Colony PCR using the primers oiG0035 and oiG0036 was conducted to check the size of the inserted fragment (expected bands at 1.1 and 1.2 kb). The sequence was verified by Microsynth using the same primers.

Construction of the rhlR regulator plasmid (piG0042)

Competent cells were transformed with piG0023 (C0171, rhlR) and selected on chloramphenicol-LB-plates. Plasmid DNA was extracted by performing a miniprep. The relevant plasmid sequence was sequenced by Microsynth using the primers oiG0001 and oiG0002. Amplification of rhlR by PCR using oiG0009 and oiG0010 resulted in the fragment fiG0006 (0.8 kb). The backbone of the vector piG0040 (lasR in pSEVA 181) was amplified by PCR using oiG0011 and oiG0012. This fragment, fiG0012 (3.2 kb), and fiG0006 were assembled using Gibbson assembly. Thus we formally replaced lasR by rhlR to construct the rhlR regulator plasmid piG0042. Competent cells were transformed with piG0042 and selected on ampicillin-LB-plates. Colony PCR using the primers oiG0035 and oiG0036 was conducted to check the size of the inserted fragment (expected bands at 1.1 and 1.2 kb). The sequence was verified by Microsynth using the same primers.

Construction of the luxR regulator plasmids with alternative constitutive promoters (piG0046 and piG0047)

The promoter site of the luxR regulator plasmid piG0041 was mutated by QuikChange site-specific mutagenesis to produce promoters of different strength. The primers oiG0031 and oiG0032 were used to establish piG0047, a plasmid with a promoter of intermediate strength (J23111). Analoguos the primers oiG0033 and oiG0034 were used to construct piG0046, a plasmid with a weak promoter (J23109). Competent cells were transformed with piG0046 and piG0047 and selected on ampicillin-LB-plates. The sequence was verified by Microsynth using the primers oig0035 and oiG0036.

BSSE Openhouse Day

Saturday, May 10th

Sharing our iGEM and synthetic biology interest with the public

On May 10th the public in Basel had the unique chance to get an insight into many different scientific laboratories and the work done there. It was the joint open house day of D-BSSE of ETH (Department of Biosystems Science and Engineering) and the Biozentrum of the University of Basel. The many different labs opened their doors to the public and many scientists were present to give interested people some details about their daily work. So did the ETH iGEM team 2014. The team was present with a poster showing the history of iGEM, the previous ETH iGEM teams with their projects and general information about synthetic biology. Additionally there was a slideshow giving a best-of photo collection of last years jamboree. The goal of this day was to inform the public about synthetic biology in general and specifically about the spirit and the many different projects of iGEM. Many people showed strong interest in truly student driven projects and are curious to follow our team wiki for the next months.

Max and Nadine participating to BSSE Openhouse event and sharing iGEM and their synthetic biology interest to the public

Week 12 : Nice cross-talk results, problems with producer strains, and with synthesis of our Las riboregulated sensor

Wednesday, August 13th

We have a lot of results for cross-talk experiments. Check the corresponding article for more details. For the moment lux promoter doesn't respon to other AHLs. This is a good step towards orthogonality.

Current challenges :
- AHL producer strains are not producing enough. We have to improve the RBS.
- GenScript has problems to produce our Las sensor with riboregulator RR42.

We have a project description !

Week 11 : PDMS chip built, First quorum sensing experiment

Wednesday, August 6th

We have a first draft of our abstract.
We have results for our first quorum sensing experiment .
We have now a proper PDMS chip for diffusion experiments.
We have a simple GFP production model for simulation of these quorum sensing experiments.
In the next weeks we will fit quorum sensing parameters thanks to the first quorum sensing experiments and our simple GFP production model, refine this Comsol diffusion model with the right quorum sensing parameters and then fit this diffusion model to diffusion experiments to find the diffusion constant.

Week 10: Chip design, Plasmid assembly, Bead production

Wednesday, July 30th

We designed two possibilities for the chip: either cells laying on agar or punched cylinders in the agar.

Comsol simulations of a part of the future chip, in two different designs : droplets of cells laying on the agar or introduced in a punched cylinder in the agar. Cells are producing AHL which diffuses through the channels.

8 out of 21 plasmids were positively sequenced. 7 further plasmids are sent for sequencing.
We will start cross-talk experiments this week. It should help us choose an orthogonal AHL pair among three different quorum sensing systems.
We have started to learn bead production.

One of our first alginate beads

REDIRECT Team:ETH Zurich/labblog/20140829mod

Week 9: First simulations, Skype with Paris Bettencourt, Chip fail

Wednesday, July 23rd

We started to simulate diffusion experiments on a Comsol model. We consider cells will lay on agar for the moment.

We will have a chip with these four different channels 1 to 4 mm long. The model still has to be refined because at the moment it doesn't take into account internal/external concentrations of AHL.

Our first mold didn't enable us to peal the PDMS correctly. We have to make it less deep.

5 of 8 regulator plasmids are done. We have to repeat construction of producer plasmids.
Parameter estimation for integrases is not working at the moment.
We skyped with Paris Bettencourt for human practice collaboration and are participating to their newsletter project.

Week 8 : Plasmdis assembly, First mold 3D printed

Wednesday, July 16th

Our first Gibson assemblies worked well. Regulator plasmids piG0040, piG0041 and piG0042 have been constructed :

Regulator plasmids construction plan

We printed our first mold for millifluidic chip :

Our first mold for millifluidic chip

We simulated the whole model with and without riboswitch in Matlab with random parameters for integrases. We are still trying to estimate integrase parameters from the literature but it is very difficult.

Week 7: Human practice planning, Plasmid assembly running, Logo design

Wednesday, July 9th

We have a logo !

In the lab, we did some :
- Plasmid preparation
- Sequencing
- Digests
- Purification of backbone fragments needed for GA

On the modeling side, we tried to estimate integrase parameters from the paper from Bonnet et al. ^[9], more particularly with the figure S4 :

Data we are using from the Bonnet et al. ^[9] paper

We are trying several strategies : minimization of the error function and Markov Chain Monte Carlo.

We have a precise plan for our human practice project. We would like to study the emergence of complexity in many different fields and investigate how people deal with it. We will do this with interviews of experts in different fields, and with a survey for a wider outreach. We will also reach younger people by organizing talks in schools. We will finally give our own advice on the question by writing an essay on the subject and linking it to our experience with Mosaicoli.

First cross talk experiments

Friday, 11th August

After having constructed the necessary regulator and sensor plasmids we were able to start first cross talk experiments. Therefore we transformed competent cells with different combinations of regulator and sensor plasmids. One example would be the strain siG0024 which contains the regulator plasmid piG0041 producing LuxR under a constitutive promoter and the sensor plasmid piG0051 that encodes for sfGFP. The latter is under control of a pluxR promoter, hence it will be transcribed in the presence of LuxR and Lux. To assess crosstalk and leakiness we conducted multiple experiments: after adding one of the three AHLs to the cultures we analyzed the raise in sfGFP production using a microtiterplate reader. In a first step we measured the dose response of constructs with different ribosomal binding sites (RBSs) and with or without riboregulator. We could observe differences not only in sensitivity, but also in leakiness; some strains expressed GFP even without AHL induction. To give an example: we evaluated the sensitivity of the siG0024 strain to different concentrations of 3OC₆-HSL (LuxI product) and compared its characteristics to those of other constructs. Additionally, we measured the sensitivity of siG0024 to 3OC₁₂-HSL (LasI product) and C₄-HSL (RhlI product). Indeed, we could observe the induction of sfGFP transcription by comparably low levels of 3OC₁₂-HSL. Crosstalk can be observed between the Las and the Lux system. To simulate a situation most similar to the final experiment, we added the diluted supernatant of AHL producer cells to the test cultures. However, we could not detect any GFP production as reaction to the supernatant. We assume that the AHL concentration is not high enough to induce transcription. By constructing stronger RBSs on the producer plasmids we aim at increasing the AHL production. All these informations we will use to design a system tailored to our plans.

Summary of cross-talk experiments results

The figure shows the dose response of xxx to 3OC₁₂-HSL, 3OC₆-HSL and C₄-HSL. Both 3OC₁₂-HSL and 3OC₆-HSL induce production of GFP, although at different concentrations. This is an example for cross talk between the lux and the las system.

Week 6: Project planning, Gibson assemblies planning, First Matlab simulations

Wednesday, July 2nd

We have a clear organization of the different experiments we would like to perform.

We want to optimize quorum sensing to have non-leaky non-cross-talking constructs. We want to prevent cross-talk between integrases and check their dynamics with different quorum sensing promoters. Then we will test the XOR gate without production of LuxI, to check how it works without the loop, and we will finally test our final construct with the loop, hoping that the delay between GFP production and the possible second switching due to AHL production is long enough to have enough fluorescence.

The red line is our critical timeline. Numbers of days are very optimistic,therefore we multiply the whole timeline by 2. The stars stand for modeling inputs.

Tasks organization with critical timeline in red.

We have also clear plans for the Gibson assemblies to perform. As an example, here is the plan for regulator plasmids :

Exemple of Gibson assembly plan for regulator constructs

We have a facebook page !

We simulated quorum sensing without leakiness on Matlab, with parameters from the literature.

Week 5: Assembly strategy and steady states derivation

Wednesday, June 25th

We will use Gibson assembly to assemble our constructs, and have now a construct assembly strategy. We know the list of experiments we want to carry (cross-talk between quorum sensing molecules, quorum sensing leakiness with or without riboswitch, cross-talk between integrases, integrase activity and logic gate behaviour) and the exact sequences of base units we will assemble (lux, rhl, las promoter and repressor units, reporter units, logic units with 3 different integrases, constitutive AHL production units for diffusion test, backbone units).

Exemple of sequences of base units.

From the modeling side, we calculated analytically the steady state of the integrase and terminator modules, and it appears that the deterministic model gives a binary steady state corresponding to an XOR gate. This is what we expected, it confirms that deterministic model in our case is interesting for the study of dynamics of the whole system, and not for steady state calculations. So we are now moving to dynamic studies.

Week 4: Improving plasmid design, Modularization of the whole model

Wednesday, June 18th

We improved a little bit the plasmid design, determined which parts will be taken from the iGEM registry, and which parts we have to synthesize.

Second draft of plasmids. The repressors production genes have been moved to the sensor plasmid in order to distribute more evenly the number of kb.

Sensor plasmids will be approx. 9.3kb long, and logic plasmids will be approx. 5,2kb long.

From the modeling side, the whole model has been modularized and we have calculated and simulated steady state for the quorum sensing module.
GeneScript, Microsynth, EraSynbio are willing to support us !

Week 3: Plasmid design started, Modeling started

Wednesday, June 11th

We started plasmid design :

First draft of plasmids. The sensor plasmid is the same in every cell. Different logic + repressors plasmids are present in cells p and q. The logic + repressors plasmid from cells p is producing the quorum sensing molecule p, and another version is present in cells q which produces QSq. Colonies of p and q cells will be arranged in an alternate way on the millifluidic chip. Here as an example we use the lux system for p cells and the rhl system for q cells.

ΦC31 and Bxb1 are integrases. LuxR an RhlR are quorum sensing repressors. A riboswitch construct is placed around quorum sensing constructs to prevent leakiness of lux and rhl promoters. Type p colonies produce AHL by expressing the enzyme LuxI. Type q colonies produce Rhl by expressing the enzyme RhlI. In fact, we don't know yet which quorum sensing systems we will use. We will have to perform cross-talk experimetns in order to choose the ones that are the most orthogonal.

We tried to print our first agar millifluidic chip : we printed it too small, and the printer had resolution problems.
We wrote all reactions and found parameters from the literature for our model.

Week 2: Investigating microfluidics, Writing a modeling pipeline

Wednesday, June 4th

This week, we have talked with people from the microfluidics group and it came out that we should be able to use beads to encapsulate our cells and use a microfluidic chip. Therefore we will try to develop this possibility in parallel with the 3D-printed agar chip.
We have set up a modeling pipeline. We divided the modeling project into 3 parts :

diffusion,
parameter fitting,
modeling of the genetic circuit itself, which comprises
- a deterministic model
- a stochastic model.

We know that the modeling challenges will be to model how integrases work, and to model the delay between reception of a quorum sensing signal and production of a quorum sensing signal by the receiver cell. Indeed, a colony could switch itself OFF when it should be ON, if it receives QS1 and produces QS2, for example. If a delay is present between reception of QS1 and production of QS2, the colony will produce GFP before it is switched OFF, and as GFP is stable enough, it will stay visible during a long time and the self-switching OFF won't be observed. This delay should be modeled.

Week 1 : Project selected

Wednesday, May 28th

After more than one month of endless meetings and passionate debates, we finally chose the project that will keep us occupied in the next five months. From the beautiful pattern made by the Sierpinski triangles, we will focus on cellular automata and try to implement one.

Sierpinski triangles appear when the rule 90 is followed by every cell on the grid :

Pattern given by rule 90 if only one cell is switched on in the first row at the beginning. The pattern appears row by row.

Ideally we will use a microfluidic chip. We could also use a 3D printed agar plate like this one to load the colonies. On this grid we can implement the rule 6, which is the simplification of rule 90 considered as a rule with 2 inputs : each cell computes a simple XOR gate of its two parents.

Arrangement of p and q cells on the chip

Pattern given by rule 6 if only one cell is switched on in the first row at the beginning. The pattern appears row by row.

The logic part will be built with integrases and the colony-to-colony communication will use quorum sensing.

Every colony will receive two quorum sensing signals (QSp and QSq) from the two cells above it. These two signals trigger the production of two different integrases r and s in the colony. Integrases enable to build biological XOR logic gates by switching twice a terminator. Indeed, every integrase can switch the terminator only once. Thus if the colony produces only r or only s, the terminator is switched only once, so the terminator is OFF, and GFP and QS1 or QS2 are produced (depending on the colony). If the colony produces r and s, the terminator is switched twice, so it is ON and it blocks expression of GFP and of the quorum sensing molecule.

Rule that will be computed by all cells : an XOR gate between the signals from the 2 cells above. Biologically, integrases p and q are able to bind sites around a terminator and switch this terminator, thereby turning off the effect of the terminator and enabling gfp transcription. If p and q integrases are both present, the terminator is switched twice and comes back to its initial state, gfp is not transcribed.

We need to :

find orthogonal quorum sensing molecules and orthogonal integrases
discuss with microfluidics experts to check if using microfluidics is possible and presents advantages in our case
find possible parts in the registry for integrases, and design plasmids

@@ Line 16: / Line 16: @@
 {{:Team:ETH_Zurich/labblog/20140820meet}}
 {{:Team:ETH Zurich/labblog/20140705}}
-{{:Team:ETH Zurich/labblog/20140709meet}}
+{{:Team:ETH_Zurich/labblog/20140510hum}}
 <html> </ul> </html>
@@ Line 25: / Line 25: @@
 {{:Team:ETH Zurich/labblog/20140723meet}}
 {{:Team:ETH Zurich/labblog/20140716meet}}
+{{:Team:ETH Zurich/labblog/20140709meet}}
 {{:Team:ETH_Zurich/labblog/20140811}}
@@ Line 34: / Line 34: @@
 {{:Team:ETH Zurich/labblog/20140604meet}}
 {{:Team:ETH Zurich/labblog/20140528meet}}
-{{:Team:ETH_Zurich/labblog/20140510hum}}
 {{:Team:ETH Zurich/tpl/foot}}

Team:ETH Zurich/blog