Team:StanfordBrownSpelman/Biodegradability

From 2014.igem.org

Revision as of 09:23, 16 October 2014 by Angelofspeed (Talk | contribs)

Stanford–Brown–Spelman iGEM 2014 — Amberless Hell Cell

Approach & Methods
Methods here.


Figure 1. Figure caption here.
Results
Our goal for this project was not only to isolate biodegradation enzymes but also to control the release of these enzymes, so that our UAV would not degrade uncontrollably. In order to control the initiation of biodegradation, we first considered using a pressure sensor. This would allow the UAV to begin degrading after the impact of a crash. The 2008 Tokyo Tech iGem team found that the ptet promoter was pressure sensitive and increased its activity 3-fold after undergoing 30 MPa of pressure. We got their construct from the distribution kit and tested its functionality by monitoring GFP expression. We found that this promoter is always turned on even at very low pressures (The cells were bright green even with no pressure at all). When we introduced a repressor for the Ptet promoter, we found out that the repressor is too strong, and even at high pressures, the Ptet promoter will still be repressed. The photo and graphs below show our testing of the Ptet promoter in the presence and absence of the Tet repressor.



This graph shows that there was not a clear correlation between the amount of pressure applied on the ptet promoter to the amount of GFP expression: For instance, application of 14000rpm pressure on cells with ptet promoter for 30 seconds led to production of less fluorescence than application of 5000rpm pressure to the same batch of cells.When Tet Repressor was used, its effect was too strong and we could not find a repressor that could inhibit ptet just enough to control the biodegradation process
On top of testing the ptet promoter, we analyzed the impact a crash would have on our UAV by using a force plate and we found it unlikely that the impact of the crash would ever reach such a high pressure (see graph below).

JEANETTE OR JOVITA PLEASE INSERT THE PRESSURE/FORCE PLATE GRAPH HERE. IT IS NOT IN THE GOOGLE DRIVE SO I CAN'T DO IT.'

We next tried to initiate degradation using a light sensor, which would activate degradation in the darkness, allowing our UAV to have a flight time of one day. We planned to do this using the construct from the UT Austin and UCSF 2004 Coliroid project. However, the strain of E. coli (EnvZ) that we needed to work with to use this construct was resistant to all 4 of the main antibiotics we had in our lab, making the bacteria difficult and expensive to work with. Finally, we decided to use quorum sensing as a means of creating a time delay for initiation of degradation. Two previous constructs, BBa_I13202 and BBa_T9002, when combined, create a quorum sensing cascade used to initiate expression of GFP. We ligated these two parts together to create our novel part, BBa_K1499500, which we used for our assays. We found that, in lac deficient cells, the quorum sensing construct can be initiated by induction with IPTG. After this induction, GFP expression increases with time, implying that the construct is doing its job. Our data for this assay is shown below.


Quorum Sensing Data




Figure 1. Flow-Cytometer Data & Graphs:
The three graphs and tables above represent the flow-cytometer data obtained from three samples of lac-deficient E. coli cells. One of the samples was a negative control of LB-cultured E. coli cells (Negative Control), and the other two samples (IPTG-Positive and IPTG-Negative) had the GFP-quorum sensing construct. The IPTG-Positive sample had a ~6X increase in GFP expression over the background IPTG-Negative cells, showing our construct worked correctly.
Flow-cytometry is a laser-based technology that has a wide-range of uses, including multiparametric cell counting and cell sorting. In this study, we utilized the cell counting ability of a flow cytometer in order to determine how many of our cells were expressing GFP after being induced with IPTG (a lac analog). The “X-Median” seen on the three tables above shows the fluorescence intensity of all of the cells that were counted that were not considered dead (Median). Each sample measured 50,000 cells (Seen under All Events - Count), and then counted all of the cells that were alive (Median - Count), where each sample had between 47,000 and 49,000 live cells. From the data, and as illustrated in the graphs above, we can gather that the fluorescence intensity (X-Median) of the LB only cells was approximately 63 arbitrary fluorescence units (AFU), the IPTG-negative cells was ~17,000 AFU, and the intensity of the IPTG-positive cells was ~107,000 AFU, meaning that the IPTG-positive quorum sensing cells increased fluorescence intensity over 6X the background intensity (IPTG-negative cells). These results indicate that our quorum sensing construct works and greatly increases GFP expression when activated through IPTG-induction. The IPTG-negative cells also expressed some non-negligible degree of GFP, which suggests that the construct could still be improved further. However, the successful proof of concept of our quorum sensing construct is incredibly promising and allows us to proceed toward the next step. Since we know that the quorum sensing construct is functional and inducible with IPTG. We can now work towards replacing the GFP gene with the genes for our degradation enzymes, allowing us to control degradation by applying IPTG at different time points.

In conjunction with working on controlling the initiation of degradation, we simultaneously worked with two degradation enzymes, esterase and cellulase. Both of these genes are isolated from the organism Neisseria sicca; the esterase is designed to de-acetylate cellulose acetate (our building material), and the cellulase breaks down the leftover cellulose into glucose monomers. After successfully transforming the esterase gene into E. coli, and confirming via colony PCR, we grew up a large culture of transformed cells and used this to extract and purify the esterase protein. The protein gel confirmed that we had isolated the esterase protein, which is present near 43 kDa on the gel.



Image description goes here.




This is the SDS-page gel that was run after purifying the esterase protein from bacteria. The band is at 43 kDa, which is the expected size of the esterase protein.


Once we had isolated our protein we were able to do functional assays with the esterase enzyme. By using a cellulose-binding dye that selectively binds to cellulose and not cellulose acetate, we were able to test whether or not the esterase enzyme was effective in de-acetylating commercial grade cellulose acetate. We soaked the cellulose acetate in the esterase protein at its optimal temperature of 30ºC and tested with the stain at multiple points. The results of our assay (shown below) demonstrate that over time the protein was working to degrade the cellulose acetate, as the blue stain intensity increased over time.



This image shows the results from our staining assay on cellulose acetate. The pieces of cellulose acetate were soaked in esterase enzyme for varying amounts of time before their level of degradation was tested using the blue cellulose-binding dye.


We are currently working on functional assays of the cellulase gene, and have submitted it as a BioBrick (BBa_K1499501).
References
Suspendisse volutpat sem eu ornare tincidunt. Mauris pharetra sed justo vitae sodales. Nulla in sodales tortor, placerat tempor dui.
Additional Information
Try to avoid having any additional information here. We're trying to keep our site organized, clean, and compelling!
Built atop Foundation. Content &amp Development © Stanford–Brown–Spelman iGEM 2014.