Team:METU Turkey safety

From 2014.igem.org

(Difference between revisions)
 
Line 151: Line 151:
-
<!--  Block of content 3 -->
 
-
<table width="100%"  cellspacing="0" height="500px">
 
-
<tr>
 
-
<td  bgColor="#F7A541"></td>
 
-
<td width="975px" align="center" bgColor="#F7A541" >
 
-
<table  width="975px"  cellspacing="0" height="500px">
 
-
<tr>
 
-
<td width="95%" bgColor="#F7A541"  rowspan="3" align="center">
 
-
 
-
<!-- Content goes here -->
 
-
 
-
<img src="https://static.igem.org/mediawiki/2014/7/7d/Gears.png">
 
-
<h3> Who will our project help?</h3>
 
-
<p> Our project will help the environment to become cleaner.</p>
 
-
</td> 
 
-
 
-
 
-
<!-- This is the back to top section -->
 
-
</table>
 
-
 
-
 
-
</td>
 
-
<td bgColor="#F7A541"></td>
 
-
</tr>
 
-
</table>
 
-
<!-- end of Block-->
 
-
 
-
 
-
<!--  Block of content 4 -->
 
-
<table width="100%"  cellspacing="0" height="500px">
 
-
<tr>
 
-
<td  bgColor="#F45D4C"></td>
 
-
<td width="975px" align="center" bgColor="#F45D4C" >
 
-
 
-
<table  width="975px"  cellspacing="0" height="500px">
 
-
<tr>
 
-
<td width="95%" bgColor="#F45D4C"  rowspan="3" align="center">
 
-
<!-- Content goes here -->
 
-
 
-
<img src="https://static.igem.org/mediawiki/2014/9/96/Camurpet.jpg">
 
-
<h3>Why did we choose this project?</h3>
 
-
<p> The biodegradation of plastic bottles took thousands of years, and the degrading process emits toxic chemicals into the air. Our project aims to clean enviroment with the degredation of PET to pyruvate by E.coli. With this project,while  the environment will be cleaned from PET, the E.coli would add pyruvate to the cell cycle and use it as a new source. </p>
 
-
 
-
</td> 
 

Latest revision as of 01:14, 18 October 2014

Team:METU Turkey/Templates/Navigationbar

HOME TEAM PROJECT PARTS MODELING INTERLAB STUDY
POLICY&PRACTICE CHARACTERIZATION SAFETY ATTRIBUTIONS GALLERY PROTOCOLS

An importat issue: Safety!

All projects are being conducted in lab-safe strains of E.coli and P.putida. All researchers have been trained in applicable lab safety to insure that no bacteria are inadvertently released into the environment. We have also been trained in proper handling of chemicals. In plastics projects, the actual organisms being engineered were maintained in lab conditions (cultures, bioreactors, etc.). None of the parts we made this year raise any particular safety issues that we can foresee. All of our major parts were either taken from pre-registered biobricks, None of our new parts would provide any foreseeable selective advantage in the wild. Thus, these parts would not increase bacterial survival in the case of accidental release.

Is there any possible situation against to our kill-switch mechanism?

Our kill switch mechanism is dependent to arabinose, so our organism would die absence of it. Its basic logic is to addict the organism our wanted enviromental conditions, so it can be controlled.

Safety Questions & Answers

1.Would any of your project ideas raise safety issues in terms of:

RESEARCHER SAFETY?

There are no hazardous chemicals that we used in the laboratory except for EtBr that we used in a special room for gel visualization and some buffers used in commercially available kits.

PUBLIC SAFETY?

Since all the organisms used in the wetlab are destroyed after they are done working with they pose no danger for public safety. We use E.coli strain DH5alpha which is easy to kill and all the student members who work in the wetlab are very well trained to make sure there is no unwanted contamination. This year we are also working on a kill switch which, if works properly, will eliminate any bacteria whereas they will not be able to survive without Arabinose present.

ENVIRONMENTAL SAFETY?

As mentioned above a kill switch will be available in the organism which will initiate cell death when the cell is in an environment that does not contain enough Arabinose.

2. Do any of the new BioBrick parts (or devices) that you made this year raise any safety issues?

We have followed all the safety procedures during the isolation process from the cells we had and we successfully isolated the DNA without any problems that will raise safety issues.

3.Is there a local biosafety group, committee, or review board at your institution? If yes, what does your local biosafety group think about your project? If no, which specific biosafety rules or guidelines do you have to consider in your country?

In our university we have a biosafety and ethical research center which monitors the safety of our projects. http://www.ueam.metu.edu.tr The members of METU Biology department are also members of National Biosafety Coordinating Committee. We are able to consult to them whenever it is necessary. Also biosafety is a very important subject for METU Department of Biology, whereas the student members are very well trained in the subject. Also the projects that we decided to work on are presented to many people in the area in order to see if they are of any concern for the biosafety regulations. All the procedures that are used in the lab are also approved procedures that are used by these people mentioned above.

4. Do you have any other ideas how to deal with safety issues that could be useful for future iGEM competitions? How could parts, devices and systems be made even safer through biosafety engineering?

We believe using specific strains designed specifically for labwork will be safer. It is possible to genetically modify the organisms so that, they are not able to grow outside the lab environment. There probably is not a way to build some biobricks that can be modified in order to make them safer since their function will be the cause of safety issues.

Our Supporter: