The team received mandatory safety training and general lab routine information.

A really cool video about Chalmers' chemical safety routine (recorded at our very own lab!) can be seen in http://www.chalmers.se/insidan/EN/about-chalmers/environmental-work/policies/chemical-safety-routine

As a part of the mandatory training required by the SysBio group, the team received instructions on how to operate the centrifuges and autoclaves of the labs.

We also worked on our risk declaration; a mandatory document containing our experiments descriptions and information about the chemicals we are going to use, their handling, storage and associated risk, as well as waste handling.

Our Risk Declaration was approved by the lab manager and our supervisors. We also sign a safety certificate stating that we are aware of the safety instructions and with that, completed the mandatory "check-in list for new incomers" of the lab.

On the first day of laboration, we prepared LB, YPD and SC-Ura/His/Trp-Leu and YPD media.
Click here to see the protocol. [[PUT METHOD]]!
[[File:20140623_103124.jpg]],[[File:20140623_115809.jpg|frameless|300px]]

Succesfully PCR amplified five out of the seven parts from yeast genome via a Phusion High-Fidelity DNA Polymerase.
Click here to see the protocol. [[PUT METHOD]]!

The PCR program used was:

1. 3 min at 98ºC
2. 10s at 98ºC
3. Gradient from 52 to 61ºC for 30s
4. 1 min at 72ºC
5. Go to step 2 (repeat 39 times)
6. 10 min at 72ºC.

A diagnostic gel was performed and the result was as follows: [[File: Bio-Rad 2014-06-25 15hr 34min.jpg|frameless|300px]]

The purification of the succesfully amplified parts was done using a PCR Purification Kit from GenJet following the instructions of the manufacture's manual but with no addition of isopropanol.

Plasmid Purification

Performed plasmid purification on E. coli cells containing plasmids p413, p414, p415, p416, p2055 and a plasmid containig our Cas9 sequence (pTPG1-dCas9-UPGP)via a GenJet Plasmid Purification Kit. The manufacter's instructions were followed, except the elution buffer was subtituted by water on the last step.

Amplification and purification of parts

Performed a PCR amplification of the non-synthetic parts that failed on the day before and on the dCas9 sequence and the three fluorescent proteins -Yellow, Cyano and Red (YFP, CFP and RFP, respectively).

The PCR was done using the Phusion High-Fidelity DNA Polymerase (see protocol here) and the program used was:

1. 3 min at 98ºC
2. 10s at 98ºC
3. Gradient from 50 to 55ºC for 30s
4. 30s at 60ºC
5. 2min 15s at 72ºC
6. Go to step 2 (repeat 39 times)
7. 10 min at 72ºC.

A diagnostic gel was performed and the result is as follows:
[[File: Bio-Rad 2014-06-26 17hr 53min.jpg|frameless|300px]]

Gel extraction

Extracted the fluorecent proteins amplified on the day before with a GeneJet gel extraction kit.The manufacter's instructions were followed, except the elution buffer was subtituted by water on the last step.

PCR amplification and merging

Performed a PCR to fuse the pDSE4, pHO and dCas9 parts together.

The PCR was done using the Phusion High-Fidelity DNA Polymerase (see protocol here) and the program used was:

1. 3 min at 98ºC
2. 10s at 98ºC
3. Gradient from 50 to 55ºC for 30s
4. 30s at 60ºC
5. 2min 15s at 72ºC
6. Go to step 2 (repeat 39 times)
7. 10 min at 72ºC.

A diagnostic gel was performed and the result is as follows:
[[File: Bio-Rad 2014-06-27 15hr 07min-2.jpg|frameless|300px]]

The bands did not seem correct, so this PCR was repeated on the next day.

PCR amplification and merging

Repeated the PCR to fuse the pDSE4, pHO and dCas9 parts together.

The PCR was done using the Phusion High-Fidelity DNA Polymerase (see protocol here) and the program used was:

1. 3 min at 98ºC
2. 10s at 98ºC
3. 50ºC for 30s
4. 58ºC for 30s
5. 2min 15s at 72ºC
6. Go to step 2 (repeat 39 times)
7. 10 min at 72ºC.

A diagnostic gel was performed and the result is as follows:
[File: Bio-Rad 2014-06-30 15hr 24min.jpg|frameless|300px]]

This did not seemed to work either.

Plasmid restriction

Cleaved the plasmids p413TEF, p414TEF, p415TEF and p416TEF by using the enzymes SacI and XbaI.

Approximately 500ng of each plasmid was mixed with o.5UL of SacI, 0.5UL of XbaI, 2UL of FastDigest buffer, 1UL of FastAP (alkaline phosphatase) and up to 20 UL of deionized sterile water.

This reaction mixture was incubated at in a water bath at 37ºC for 10 minutes and then enzymatic inactivation was performed for 5min in a heating block at 60ºC.

PCR amplification and merging

The PCR was done using the Phusion High-Fidelity DNA Polymerase and the program used was:

1. 3 min at 98ºC
2. 10s at 98ºC
3. 50ºC for 30s
4. 58ºC for 30s
5. 2min 30s at 72ºC
6. Go to step 2 (repeat 40 times)
7. 10 min at 72ºC.

A diagnostic gel was performed, however the sizes of the resulting fragments did not match the expected.

Plasmid restriction

Cleaved the plasmids p413TEF, p414TEF, p415TEF and p416TEF by using the enzymes SacI and XbaI.

Approximately 500ng of each plasmid was mixed with o.5UL of SacI, 0.5UL of XbaI, 2UL of FastDigest buffer, 1UL of FastAP (alkaline phosphatase) and up to 20 UL of deionized sterile water.

This reaction mixture was incubated at in a water bath at 37ºC for 10 minutes and then enzymatic inactivation was performed for 5min in a heating block at 60ºC.

Samples were loaded into a gelGreen, that showed p413, p415 and p416 approximately in the 5000bp size band, while p414 presented two bands, one around 4000bp and another at 2000bp.

this indicates that the 5000bp band corresponds to the uncut plasmid, while the 4000bp and 2000bp are probably contaminations.

Plasmid restriction

Cleaved the plasmids p413TEF, p414TEF, p415TEF and p416TEF by using the enzymes SacI and XbaI.

Approximately 500ng of each plasmid was mixed with o.5UL of SacI, 0.5UL of XbaI, 2UL of FastDigest buffer, 1UL of FastAP (alkaline phosphatase) and up to 20 UL of deionized sterile water.

This reaction mixture was incubated at in a water bath at 37ºC for 10 minutes and then enzymatic inactivation was performed for 5min in a heating block at 60ºC.

PCR amplification

Amplified the parts pDSE4, cas9 and pHO. The PCR was done using the Phusion High-Fidelity DNA Polymerase and the program used was:

1. 3 min at 98ºC
2. 10s at 98ºC
3. 50ºC for 30s
4. 58ºC for 30s
5. 2min 15s at 72ºC
6. Go to step 2 (repeat 40 times)
7. 10 min at 72ºC.

A diagnostic gel was performed, however the sizes of the resulting fragments did not match the expected.

PCR amplification

Repeated the amplification of the parts pDSE4, cas9 and pHO. The PCR was done using the Phusion High-Fidelity DNA Polymerase and the program used was:

1. 3 min at 98ºC
2. 10s at 98ºC
3. 50ºC for 30s
4. 58ºC for 30s
5. 2min 15s at 72ºC
6. Go to step 2 (repeat 40 times)
7. 10 min at 72ºC.

A diagnostic gel was performed and the sizes of the fragments matched for the pDSE4 and pHO, but not for the Cas9.


Gel extraction

Extracted the DNA fragments previously amplified with a GeneJet gel extraction kit.The manufacter's instructions were followed, except the elution buffer was subtituted by water on the last step.

Concentration determination

The concentration of all the fragments obtained was measured via a NanoDrop. The samples were measured in duplicates. The results ranged from 8.5 ng of DNA per UL to 42ng/UL.

Plasmid purification

Performed plasmid purification on E. coli cells containing plasmids p413, p414, p415, p416 and p2055 via a GenJet Plasmid Purification Kit. The manufacter's instructions were followed, except the elution buffer was subtituted by water on the last step. Each plasmid was purified in duplicates.

Plasmid restriction

Cleaved the plasmids p413TEF, p414TEF, p415TEF and p416TEF by using the enzymes SacI and XbaI.

Approximately 500ng of each plasmid was mixed with o.5UL of SacI, 0.5UL of XbaI, 2UL of FastDigest buffer, 1UL of FastAP (alkaline phosphatase) and up to 20 UL of deionized sterile water. Control tubes containing just one of the enzymes each were also prepared.

This reaction mixture was incubated at in a water bath at 37ºC for 10 minutes and then enzymatic inactivation was performed for 5min in a heating block at 60ºC.

A diagnostic gelGreen was performed and showed that the cleavage of plasmids p413, p415 and p416 was successful.

Gel extraction

Extracted the cleaved plasmids with a GeneJet gel extraction kit.The manufacter's instructions were followed, except the elution buffer was subtituted by water on the last step.

Concentration determination

The concentration of the circular and linear plasmids obtained was measured via a NanoDrop. The samples were measured in duplicates. The results ranged from 6.55 ng of DNA per UL to 543.4ng/UL.

Plasmid restriction

Cleaved the plasmids p414TEF with the enzymes SacI and XbaI.

Approximately 500ng of the plasmid was mixed with o.5UL of SacI, 0.5UL of XbaI, 2UL of FastDigest buffer, 1UL of FastAP (alkaline phosphatase) and up to 20 UL of deionized sterile water. Control tubes containing just one of the enzymes each were also prepared.

This reaction mixture was incubated at in a water bath at 37ºC for 10 minutes and then enzymatic inactivation was performed for 5min in a heating block at 60ºC.

A diagnostic gelGreen was performed and showed multiple size bands for the samples treated with XbaI. Consultation to the literature showed that this enzyme has not an unique restriction site for p414.

Therefore the restriction was repeated with the enzyme SpeI, that has an unique cleavage site in p414 located 6bp away from the XbaI's desirable cleavage site. The same procedure described above was used, substituting XbaI for SpeI.

The disgnostic gel performed on this second cleavage showed correct band sizes, but with too low lines. This indicates low concentration of the plasmid, therefore it was not extracted.

Plasmid restriction

Cleaved the plasmids p414TEF with the enzymes SacI and SpeI.

Approximately 500ng of the plasmid was mixed with o.5UL of SacI, 0.5UL of SpeI, 2UL of FastDigest buffer, 1UL of FastAP (alkaline phosphatase) and up to 20 UL of deionized sterile water. Control tubes containing just one of the enzymes each were also prepared.

This reaction mixture was incubated at in a water bath at 37ºC for 10 minutes and then enzymatic inactivation was performed for 5min in a heating block at 60ºC.

A diagnostic gelGreen was performed and showed again too light bands or no bands at all.

Plasmid restriction

Repeated the cleavage the plasmids p414TEF with the enzymes SacI and SpeI.

Approximately 500ng of the plasmid was mixed with o.5UL of SacI, 0.5UL of SpeI, 2UL of FastDigest buffer, 1UL of FastAP (alkaline phosphatase) and up to 20 UL of deionized sterile water. Control tubes containing just one of the enzymes each were also prepared.

This reaction mixture was incubated at in a water bath at 37ºC for 10 minutes and then enzymatic inactivation was performed for 5min in a heating block at 60ºC.

A diagnostic gelGreen was performed and SacI seemed to be leaving an excessive amount of uncut plasmid while SpeI apparently degrades the sample.

PCR amplification and merging

Performed a PCR to fuse the following fragments:

The PCR was done using the Phusion High-Fidelity DNA Polymerase and the program used was:

1. 3 min at 98ºC
2. 10s at 98ºC
3. 50ºC for 30s
4. 30s at 60ºC
5. 2min 15s at 72ºC
6. Go to step 2 (repeat 39 times)
7. 10 min at 72ºC.

A diagnostic gelRed was performed and revealed the expected band sizes for the merging of D-tag with CFP and pHO with Sic1.

Gel extraction

Extracted the successfully merged fragments with a GeneJet gel extraction kit.The manufacter's instructions were followed, except the elution buffer was subtituted by water on the last step.

PCR amplification and merging

Performed a PCR to fuse the following fragments:

The PCR was done using the Phusion High-Fidelity DNA Polymerase and the program used was:

1. 3 min at 98ºC
2. 10s at 98ºC
3. Gradient from 47 to 55ºC for 30s
4. 30s at 60ºC
5. 2min 15s at 72ºC
6. Go to step 2 (repeat 39 times)
7. 10 min at 72ºC.

A diagnostic gelRed was performed and revealed the expected band sizes for the merging of D-tag with YFP.

Gel extraction

Extracted the successfully merged fragments with a GeneJet gel extraction kit. The manufacter's instructions were followed, except the elution buffer was subtituted by water on the last step.

Dissolution of synthetic parts

The received synthetic parts (g-blocks) were centrifuged at 3000g for 3min and then dissolved with 10UL of sterile water. The solution was transferred to 10UL of TE buffer, resulting in a final concentration of 10ng/UL.

Amplification and purification of synthetic parts

Performed a PCR amplification of the synthetic parts previously diluted. Namely

The PCR was done using the Phusion High-Fidelity DNA Polymerase and the program used was:

1. 3 min at 98ºC
2. 10s at 98ºC
3. 54ºC for 30s
4. 30s at 60ºC
5. 20s at 72ºC
6. Go to step 2 (repeat 39 times)
7. 10 min at 72ºC.

A diagnostic gel was performed and showed the expected band sizes for all the fragments except pCYC1.

Gel extraction

Extracted the successfully merged parts with a GeneJet gel extraction kit. The manufacter's instructions were followed, except the elution buffer was subtituted by water on the last step.

Preparation of competent cells

Following the instructions of the protocol "Frozen-EZ Yeast Transformation II" by ZymoResearch, Saccaromyces cerevisiae competent cells were prepared and stored at -80ºC.

Amplification and purification of synthetic parts

Repeated the PCR amplification of the synthetic part pCYC1 m1.

The PCR was done using the Phusion High-Fidelity DNA Polymerase and the program used was:

1. 3 min at 98ºC
2. 10s at 98ºC
3. 54ºC for 30s
4. 30s at 60ºC
5. 20s at 72ºC
6. Go to step 2 (repeat 39 times)
7. 10 min at 72ºC.

A diagnostic gel was performed and showed the expected band sizes.

Gel extraction

Extracted the successfully merged part with a GeneJet gel extraction kit. The manufacter's instructions were followed, except the elution buffer was subtituted by water on the last step.

Yeast Transformation

Performed transformation on the competent cells previously prepared according to the protocol "Yeast Transformation".

Equimollar quantities of the fragments were added to plasmids with different markers. More specifically:

Plasmid restriction

Cleaved the plasmids p413TEF and p416TEF with the enzymes SacI and XbaI.

Approximately 500ng of the plasmid was mixed with o.5UL of SacI, 0.5UL of XbaI, 2UL of FastDigest buffer, 1UL of FastAP (alkaline phosphatase) and up to 20 UL of deionized sterile water. Control tubes containing just one of the enzymes each were also prepared.

This reaction mixture was incubated at in a water bath at 37ºC for 30 minutes and then enzymatic inactivation was performed for 5min in a heating block at 65ºC.

A diagnostic gelGreen was performed and showed fragments with the correct sizes.

Gel extraction

Extracted the successfully restricted plasmids with a GeneJet gel extraction kit. The manufacter's instructions were followed, except the elution buffer was subtituted by water on the last step.

Dissolution of synthetic parts

The received synthetic part pCYC1 m2 was centrifuged at 3000g for 3min and then dissolved with 10UL of sterile water. The solution was transferred to 10UL of TE buffer, resulting in a final concentration of 10ng/UL.

Amplification and purification of synthetic parts

Performed PCR amplification of the synthetic part pCYC1 m2.

The PCR was done using the Phusion High-Fidelity DNA Polymerase and the program used was:

1. 3 min at 98ºC
2. 10s at 98ºC
3. 54ºC for 30s
4. 30s at 60ºC
5. 20s at 72ºC
6. Go to step 2 (repeat 39 times)
7. 10 min at 72ºC.

A diagnostic gel was performed and showed the expected band sizes.

PCR purification

The purification of the succesfully amplified part was done using a PCR Purification Kit from GenJet following the instructions of the manufacture's manual but with no addition of isopropanol and elution was done with 30UL of sterile water.

Concentration determination

The concentration of the pCYC1 m2 samples obtained was measured via a NanoDrop. The samples were measured in duplicates. The results ranged from 15.1 ng of DNA per UL to 34.2ng/UL.

Yeast Transformation

Performed transformation on the competent cells previously prepared according to the protocol "Yeast Transformation".

Equimollar quantities of the fragments were added to plasmids with different markers. More specifically: