Latest revision as of 00:51, 18 October 2014

Cooper Union 2014 iGEM

Hardware

OpenGelBox

OpenRoller

OpenFuge

Microfluidics

Open Source Test Tube Roller

This test tube roller is a simple and cost-effective test tube roller. It is made from 6mm acrylic, cardboard, a DC motor, a potentiometer, and one custom 3D printed hub. The potentiometer allows for variable speeds by limiting current to the motor.

Build

Plans

The mounting holes and 3-D printed hub may need to be modified based on the DC motor being used.

Parts

The following are needed to build the roller:

6mm Acrylic sheet
DC Motor
Power supply with matching voltage to motor
Potentiometer
Power Switch
#8-32 screws, nuts, and locknuts

Notes
A 12V wall wart was used for this but most appropriate power sources can be used.
Both a power switch and transistor are optional and can be used to regulate the power and speed of the motor.

Assembly

Download the original CAD files for the “motor_front” and “hub” and adjust the motor mount pattern and motor hub diameter to match the dimensions of your motor
Laser cut dxf files and your modified “motor_front” plate
3D print the motor hub
Screw together frame and motor. Use lock nuts on pivot joints
Solder the power supply to the motor with the power switch and potentiometer in series
Wrap rubber bands around test tubes before inserting into hub. This is to prevent slipping as the cardboard friction fit can sometimes slip over time

Final Assembly

Completed Assembly
The design was mainly based around the DC motor since it was the only one that could be used at the moment. Future designs can be modified to fit other DC motor's.

The hub attaches the tube holder to the motor's shaft. The hub was customized to the diameter of the shaft; it was then press fitted onto the preheated shaft to ensure a solid fit.

A second plate made of foam board was attached to provide additional support to the tubes.

The lower support arms swing to adjust the angle of the rotor head.

@@ Line 10: / Line 10: @@
 <ul class="menu">
 	<li class="menu"> <a class="menu" href="https://2014.igem.org/Team:Cooper_Union"> Home </a> </li>
-	<li class="menu"> Project
+	<li class="menu-project"> Project
 		<ul class="menu">
 			<li class="menu"> <a class="menu" href="https://2014.igem.org/Team:Cooper_Union/TdT_project">De Novo Synthesis </a></li>
-			<li class="menu"> <a class="menu" href="https://2014.igem.org/Team:Cooper_Union/Telomere_project">Programmable Lifespan</a> </li>
+			<li class="menu"> <a class="menu" href="https://2014.igem.org/Team:Cooper_Union/Telomere_project">Programmable Lifespan Timer</a> </li>
 			<li class="menu"> <a class="menu" href="https://2014.igem.org/Team:Cooper_Union/Biohack_project">Biohacker Kit </a></li>
 			<li class="menu"> <a class="menu" href="https://2014.igem.org/Team:Cooper_Union/Hardware">OpenSource Hardware </a> </li>
+						<!--<li class="menu"> <a class="menu" href="https://2014.igem.org/Team:Cooper_Union/Modeling">Modeling </a> </li>-->
 			<li class="menu"> <a class="menu" href="https://2014.igem.org/Team:Cooper_Union/Parts">BioBrick Parts </a></li>
-			<li class="menu"> <a class="menu" href="https://2014.igem.org/Team:Cooper_Union/Modeling">Modeling </a> </li>
 		</ul>
 	</li>
-	<li class="menu"> <a class="menu" href="https://igem.org/Safety/Safety_Form?team_id=1354">Safety</a> </li>
+	<li class="menu-safety"> Social
-	<li class="menu"><a class="menu" href="https://2014.igem.org/Team:Cooper_Union/Outreach"> Outreach </a></li>
+		<ul class="menu">
-	<li class="menu">   Notebook
+			<li class="menu"><a class="menu" href="https://2014.igem.org/Team:Cooper_Union/Safety">Safety</a> </li>
+			<li class="menu"><a class="menu" href="https://2014.igem.org/Team:Cooper_Union/Ethics">Ethics</a> </li>
+			<li class="menu"><a class="menu" href="https://2014.igem.org/Team:Cooper_Union/Outreach">Outreach </a></li>
+		</ul>
+	</li>
+	<li class="menu-notebook">   Notebook
 		<ul class="menu">
 			<li class="menu"> <a class="menu" href="https://2014.igem.org/Team:Cooper_Union/Protocols">Commonly Used Protocols </li>
@@ Line 28: / Line 33: @@
 		</ul>
 	</li>
-	<li class="menu"> Team
+	<li class="menu-team"> Team
 		<ul class="menu">
 			<li class="menu"> <a class="menu" href="https://2014.igem.org/Team:Cooper_Union/biofanfic">Members </a> </li>
@@ Line 41: / Line 46: @@
 </div>
+<br>
+<hr>
+<br>
 <div class="text">
 <!-----Add content below---->
+<div class="center">
+<br><h1>Hardware</h1><br>
+<div class="hardware">
+<img src="https://static.igem.org/mediawiki/2014/0/0b/CU_2014_OpenGel.png" title="The Cooper Union OpenGelBox" height="100px" width="100px" /><br>
+<span class="hardware"><a href="https://2014.igem.org/Team:Cooper_Union/OpenGel">OpenGelBox</a></span>
+</div>
+<div class="hardware">
+<img src="https://static.igem.org/mediawiki/2014/1/15/CU_2014_OpenRoller_icon.png" title="The Cooper Union Open Tube Roller" height="100"  /><br>
+<span class="hardware"><a href="https://2014.igem.org/Team:Cooper_Union/OpenRoller">OpenRoller</a></span>
+</div>
+<div class="hardware">
+<img src="https://static.igem.org/mediawiki/2014/3/3e/CU_OpenFuge-stock.jpg" title="OpenFuge" height="100"  /><br>
+<span class="hardware"><a href="http://www.instructables.com/id/OpenFuge/" target="_blank">OpenFuge</a></span>
+</div>
+<div class="hardware">
+<img src="https://static.igem.org/mediawiki/2014/4/44/CU_Micro_Sketch1.JPG" title="Macro/Micro Fluidics" height="100" width="100" /><br>
+<span class="hardware"><a href="https://2014.igem.org/Team:Cooper_Union/Microfluidics">Microfluidics</a></span>
+</div></div>
+<br><br>
+<div class="text">
+<h2>Open Source Test Tube Roller</h2>
+<br>
+<div class="center">
+<img src="https://static.igem.org/mediawiki/2014/4/4b/CU_2014_OpenRoller.png" height="400px" /></div>
-== Test Tube Roller ==
+<br><br>
-(picture)
+This test tube roller is a simple and cost-effective test tube roller. It is made from 6mm acrylic, cardboard, a DC motor, a potentiometer, and one custom 3D printed hub. The potentiometer allows for variable speeds by limiting current to the motor.
+<h2>Build</h2><Br>
+<h3>Plans</h3>
+<br>
+<img src="https://static.igem.org/mediawiki/2014/e/ee/CU_OpenRoller_CAD.PNG" width="450" /><br>
+The mounting holes and 3-D printed hub may need to be modified based on the DC motor being used.
-== Introduction ==
+<br><br>
+<h3>Parts</h3>
-The test tube roller is an open source lab equipment design. This design was created by Karlin Yeh and Wilfrido Castillo and a version of it is in the Cooper Union. This design is made from cardboard, .125" acrylic, a few electronic components and a DC motor.
+<br>
-== Build ==
-Parts
 The following are needed to build the roller:
+<ul>
+<li>6mm Acrylic sheet</li>
+<li>DC Motor</li>
+<li>Power supply with matching voltage to motor</li>
+<li>Potentiometer</li>
+<li>Power Switch</li>
+<li>#8-32 screws, nuts, and locknuts</li>
+</ul><br>
-- .125" acrylic sheet
+<em>Notes</em><br>
--DC Motor
+A 12V wall wart was used for this but most appropriate power sources can be used.<br>
--Power adapter
+Both a power switch and transistor are optional and can be used to regulate the power and speed of the motor.<br>
+<br>
-A 12V wall wart was used for this but most appropriate power sources can be used.
+<h3>Assembly</h3>
--Power switch
+<ol>
--Transistor
+<li>Download the original CAD files for the “motor_front” and “hub” and adjust the motor mount pattern and motor hub diameter to match the dimensions of your motor </li>
+<li>Laser cut dxf files and your modified “motor_front” plate</li>
+<li>3D print the motor hub</li>
+<li>Screw together frame and motor. Use lock nuts on pivot joints</li>
+<li>Solder the power supply to the motor with the power switch and potentiometer in series</li>
+<li>Wrap rubber bands around test tubes before inserting into hub. This is to prevent slipping as the cardboard friction fit can sometimes slip over time</li>
+</ol>
-Both a power switch and transistor are optional and can be used to regulate the power and speed of the motor.
+<h3>Final Assembly</h3>
+<br>
+<img src="https://static.igem.org/mediawiki/2014/b/b2/CU_OpenRoller_parts1.png" width="400" /><br>
+<em>Completed Assembly</em><br>The design was mainly based around the DC motor since it was the only one that could be used at the moment. Future designs can be modified to fit other DC motor's.<br><br>
+<img src="https://static.igem.org/mediawiki/2014/f/f4/CU_OpenRoller_parts2.png" width="400"/><br>
+The hub attaches the tube holder to the motor's shaft. The hub was customized to the diameter of the shaft; it was then press fitted onto the preheated shaft to ensure a solid fit.<br>
+<img src="https://static.igem.org/mediawiki/2014/3/36/CU_OpenRoller_parts3.png" width="400" /><br>
+A second plate made of foam board was attached to provide additional support to the tubes.<br>
+<img src="https://static.igem.org/mediawiki/2014/1/16/CU_OpenRoller_parts4.png" width="400" /><img src="https://static.igem.org/mediawiki/2014/d/dc/CU_OpenRoller_parts5.png" width="400" /><br>
+The lower support arms swing to adjust the angle of the rotor head.
+<br><br>
+<br>
--#8-32 screws, jam nuts, and locknuts
+<!--
+xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
+DO NOT EDIT BELOW HERE
+xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx -->
+</div>
+<br>
+<br>
+<hr>
-Plans
-(Need to post the dxf files and sldprt) The mounting holes and 3-d printed hub may need to be modified based on the DC motor being used.
+</div>
-Assembly
-The acrylic pieces are assembled to make the frame with screws.
-(pictures of the pieces)
+<div class="cu-footer">
+    <div class="bottom-left">
-The motor is mounted to the front piece using screws.
+        <a href="https://2014.igem.org/Team:Cooper_Union" span="The Cooper Union: μToolbox"><img src="https://static.igem.org/mediawiki/2014/b/bd/CU_2014_logo.png" height="150"  /></a></div>
+    <div class="bottom-center">
-(pictures of the motor mounted to the front piece)
+        <a href="https://2014.igem.org/Team:Cooper_Union/Project" class="black" >
+            <img src="https://static.igem.org/mediawiki/2014/2/27/CU_2014_LogoP.png" height="100" style="vertical-align: top;" title="Projects" />
-A transistor can be soldered on the wall wart to control the speed.
+            <span>Projects</span>
+        </a>
-(picture of the wall wart)
+        <a href="https://2014.igem.org/Team:Cooper_Union/Social" class="red" >
+            <img src="https://static.igem.org/mediawiki/2014/b/b2/CU_2014_logoS.png" height="100" style="vertical-align: top;" title="Social" />
-The hub and spinner plate are screwed on to the motor.
+            <span>Social</span>
+        </a>
-(picture of the spinner plate on the motor)
+        <a href="https://2014.igem.org/Team:Cooper_Union/Notebook" class="green" >
+            <img src="https://static.igem.org/mediawiki/2014/d/da/CU_2014_LogoN.png" height="100" style="vertical-align: top;" title="Notebook" />
-The test tubes slip fit onto the spinner plate.
+            <span>Notebook</span>
+        </a>
+        <a href="https://2014.igem.org/Team:Cooper_Union/biofanfic"class="blue">
+            <img src="https://static.igem.org/mediawiki/2014/3/38/CU_2014_LogoT.png" height="100" style="vertical-align: top;" title="Team" />
+            <span>Team</span>
+        </a>
+    </div>
+    <div class="bottom-right">
+        <a href="http://www.cooper.edu" target="_blank" span="The Cooper Union"><img src="https://static.igem.org/mediawiki/2014/9/90/CU_2014_Cooper_union_logo.png" height="150" /></a>
+    </div>
+</div>
-Final Assembly
-(pictures of the roller with test tubes)
-The design was mainly based around the DC motor since it was the only one that could be used at the moment. Future designs can be modified to fit other DC motor's.
+</body>
+</html>

Team:Cooper Union/OpenRoller

From 2014.igem.org