Results

In this section we will discuss the key results of fungal sensing, fungal inhbition, kill-switch.

Sensing

In literature it was never sure if there is really a fusaric acid dependent promoter. In this project we proved that there is such a promoter. A fusaric acid dependent promoter (isolated from Pseudomonas putida KT2440) was cloned in front of GFP(BBa_E0040), transformed in Pseudomonas putida KT2440 (P.putida). And flouresence were measured in different fusaric acid concentration. We were able to validate and characterize a novel fusaric acid dependent promoter (Bba_K1493000).

For more information, read fungal sensing.

Inhibition

Upon sensing fusaric acid, three genes and a gene cluster will be activated that will lead to production production of certain antifungal. Those genes and their function being:

1. phlABCDE gene cluster, able to produce 2,4-Diacetylphloroglucinol(2,4-DAPG)
2. Methionine-γ-lyase, Dimethyldisulfide (DMDS) and dimethyltrisulfide (DMTS)
3. Pfri, produce pyoverdine in pressence of iron
4. Chitinase, overexpresses chitinase activity

Methionine-γ-lyase and Pfri were bopth made into biobricks, Bba_K1493300 and Bba_K1493200 respectively. With both biobricks validated, and for Pfri characterized. Pfri has shown to give a four fold increase of pyoverdine production in the pressence of iron in the medium.

All transformants were co-inoculated with Fusarium oxysporum cubense TR4 on agar plates in order to test its inhibition ability. Controls used were wild type P.putida KT2440 with F.oxysporum and just F.oxysporum.

In general, it was hard to distinguish the increase inhibition effect of the anti-fungal producing transformants against F. oxysporum. This is because the P. putida chassis we have chosen is already very good at inhibiting F. oxysporum naturally, which probably makes it hard to see a distinguish increased growth inhibition by our synthetic, anti-fungal producing P. putida strains. However, with the Methionine-γ-lyase(MgL) strain, we have a clear indication that there is an increase of growth inhibition of F. oxysporum (figure 3) and with others, producing 2,4-DAPG, chitinase or pyoverdine, we can say that there is an indication of a slight increase of growth inhibition (figure 8, 12 and 13) on top of the natural inhibition. For more information, read fungal inhibiton.

Kill-Switch

Once fungal growth inhibitors are produced and F. oxysporum is no longer in the soil BananaGuard has done it's job and is no longer needed in the soil. Therefore we have implemented a Kill-Switch into our system, it works like a toggle-switch that knows when fusaric acid was around and once it's gone, toxins will be produced that eliminates GananaGuard itself. With the kill switch regulatory system in figure 4.

LambdaCI (induced by rhamnose) has shown to suppress pcIλ/Tet promoter and pcIλ/lac promoter by showing no GFP produced when induced with rhamnose (figure 5 and figurexx respectively). LacI was also shown to suppress pcIλ/lac by showing no GFP produced when induced with rhamnose(figure xx). The toggle-switch was constructed ( Bba_K1493702, Bba_K1493703) containing pCI/lac promoter + TetR together with ptet + LacI + GFP. After testing, it was concluded that the toggle switch can be in its resting state. Because it was to have low GFP fluorescence when induced by IPTG. In addition, the toggle switch can also be activated and be in its actives state because of high fluorescence when induced by aTc.

Promoter design model

With the kill-switch being designed, it was never quiet sure it would work as it is a pretty complicated circuit. So we looked at a statistical mechanics model has led to the experimentalists decision to opt for a new set of designed promoters and build two kill-switches in parallel. The model has predicted the newly designed promoters to have a higher stability. For more information, read kill-swtich promoter design.

Back to the lab

With new output from the promoter model, new promoters were made with different inhibitor binding sites with the BioBrick standard in mind. These promoters were then coupled in front of GFP and all 5 out of the 6 promoters we have designed have shown to work (Bba_K1493801, Bba_K1493802, Bba_K1493804, Bba_K1493805 and Bba_K1493806) . By showing GFP expression (see figure xx).

System model

Cost

Having all the whole system in P.putida is great but to keep in mind is that there is always metabolic stress in everything that we want P. putida to produce. So a model was developed that would predict the cost of the whole system. In the model it is indicated that metabolic stress is not a bottleneck for the production of fungal growth inhibitors in the activated system. For more information read system cost

Performance

Knowing that P. putida is able to handle the production of the whole system. But what about the performance of the system itself, will kill switch be able to switch or will P. putida die before anything can even happen due to toxin imbalance in the system. So we sought out a stochastic model that takes the whole system into account, the metabolic stress, the leakiness of each promoter and the toxins to see if this whole system is in anyway possible to live up to it's expectation. The following results can be seen in figure 4. For more information read model performance

Green house

Currently we have banana plants in the green house (figure 12) that have been inoculate with our engineered P. putida and also infected with F. oxysporum. However plants grow at a much slower rate when compared to bacteria. So results were not possible to obtain before the wiki-freeze (see green house ).

In short

We as an iGEM team have achieved quiet a lot during these couple of months. Here is a short list of what we have achieved:

• Validated and characterized a novel working fusaric acid dependent promoter
• Proved that pyoverdine can be produce in an iron rich environment
• Improve inhibiton of P. putida towards F. oxysporum
• Show the proof of concept of the Kill-Switch using input output plasmid
• Did an extensive characterization of the rhamnose promoter
• Have a stable toggle switch that can be activated
• Feedback loop with model and wetlab by promoter design
• Have new promoters made and validated for future iGem team to use!
• Have a model that predicts the metabolic cost of our whole system BananaGuard
• Have a model that shows the performance of our whole system BananaGuard

Apart from all things in the lab, we have also been waiting patiently to see the results of the greenhouse. How will our engineered P.putida behave in the its final application against F. oxysporum! Is it good enough in the soil? is it enough to help the banana plants? Sadly, the results were not here before the wiki-freeze however we will present them at the jamboree! So stay tuned and come to our presentation!