Team:UGA-Georgia/Notebook

From 2014.igem.org

(Difference between revisions)
Line 318: Line 318:
<br>
<br>
<h5> Week 3</h5>
<h5> Week 3</h5>
-
<li> The
+
<li> The parent strains were inoculated and grown in the varying conditions. </li>
 +
    <ul>
 +
    <li> 37C vs. 30C </li>
 +
    <li> 100mL vs. 5mL media </li>
 +
    </ul>
 +
<li> Some of each of the parent strains were also PCR tested to confirm the presence of the mCherry gene. </li>
 +
  <ul>
 +
  <li> The PCR showed that the mCherry gene was indeed present. </li>
 +
  </ul>
 +
<br>
 +
<h5> Week 5 </h5>
 +
<li> ODs of the pAW50-mCherry and the 3 colonies of 12 that were grown in varying conditions were taken and they were all above OD=0.6. </li>
 +
<li> The samples were prepared for overnight oxygen exposure as per the protocol. </li>
 +
<li> The samples were taken to the plate reader to measure fluorescence. <li>
 +
  <ul>
 +
  <li> Fluorescence was measured for all the 12 samples in each condition. </li>
 +
  </ul>
 +
<li> Since this pre-study gave us consistent, positive values for fluorescence, we were able to now refine the oxygen exposure protocol and apply it to characterization of our parts. </li>
 +
  <ul>
 +
  <li> This detailed protocol can be found in our protocol section </li>
 +
  </ul>
 +
 

Revision as of 15:51, 17 October 2014




HOME

PROJECT

WET LAB

HUMAN PRACTICES

TEAM

Notebook

February


Week 1
  • Introduction to anaerobic facilities for new members

  • Week 3
  • Making of NaS solution.
  • Making of formate media.

  • Week 4
  • Creation of transformation buffer (TB).
  • First geraniol extraction efficiency test with balch tubes.


  • March


    Week 1
  • Creation of geraniol standards for gas chromatography (GC) analysis/calibration through serial dilutions.

  • Week 3
  • Creation of more formate media.
  • Creation of general salts solution.
  • Creation of glycylglycine buffer.


  • April


    Week 1
  • Learning about ribosome binding site library (RBS) and our metabolic Optflux model.

  • Week 2
  • Made agar plates
  • Creation of fresh wild type (WT) stocks.

  • Week 3
  • Created diluted puromycin


  • May


    Week 4
  • Inoculation and revival of frozen stocks.


  • June


    Week 1
  • Determined the optical density (OD) of the previously revived cultures.

  • Week 2
  • Restriction digestion, purification, and ligation of pMEV4 and PCR products (C1 and C2).
  • Transformation by heat shock, plated the cells, made an agarose gel and ran the products on it.
  • Picked colonies from the previous day of plating.
  • Plasmid extraction, digestion, gel electrophoresis, and verification.

  • Week 3
  • Revival of pAW50-mCherry frozen stock.
  • Revival of S0001 (WT) frozen stock.

  • Week 4
  • Prepared the revived cultures for fluorescence microscopy.
  • Fluorescence microscopy training.
  • Anaerobic transformation of RBS libraries 1-12 into M. maripaludis.
  • Puromycin enrichment of transformants.
  • Made glycerol stocks of original transformants.
  • Fluorescent microscopy of transformants/pAW50-mCherry/S0001.


  • July


    Week 1
  • Took ODs of the native RBS and library 1 and 2 (12; L-1; L-2 respectively).
  • Plated the 12, L-1, and L-2 cultures.
  • Dispensed media to test tubes.
  • Picked colonies form the plates.

  • Week 2
  • ODs from last weeks picked colonies were taken.
  • Made frozen stocks of RBS colonies,
  • Sub-cultured parent strains.
  • Researched primary literature on mCherry maturation.
  • Began developing a protocol for oxygen maturation of mCherry.

  • Week 3
  • Made frozen stocks of RBS colonies and sub-cultured parent strains.
  • Re-subcultured and revive pAW50-mcherry.
  • Subcultured the parent strains of WT and native RBS (12) into triplicates. The triplicates were wrapped in foil to prevent any photobleaching.
  • The pAW50-mcherry came up and then all samples were taken to a plate reader to perform fluorescence tests.

  • Week 5
  • Filled out and submitted safety form.
  • The geraniol extraction efficiency experiment was performed.
    • Left the organic phase to dry over night and be resuspended to test for voltility.
  • Track selection.


  • August


    Week 2
  • Geraniol synthase containing cells (GS) were inoculated into triplicates of varying concentrations of puromycin.
    • The previous geraniol extraction methods were repeated with these new GS samples.

    Week 3
  • Geraniol standards were made to be test on GC/MS.
  • We did an extraction efficiency test between batch tube vs. separatory funnel.
  • Testing of geraniol on the GC/MS was done.

  • Week 4
  • Cells containing our pMEV4 plasmid with native RBS were inoculated into 5mL of rezasurin free (RF) media with varying levels of puromycin concentration.
  • ODs were taken of the samples and they were placed into darkness.

  • Week 5
  • The cells were prepared for the plate reader as per the first plate reader preparation protocol.
  • The plate reader results were in conclusion and a new protocol was required.


  • September


    Week 2
  • A frozen stock of pAW50-mCherry was revived in 5mL of RF media.
  • Room temperature stocks of 3 colonies of 12 were inoculated into 5mL of RF media.
    • All of these will act as parent strains that will then be inoculated and grown in varying conditions to test for the best condition for generating mCherry.

    Week 3
  • The parent strains were inoculated and grown in the varying conditions.
    • 37C vs. 30C
    • 100mL vs. 5mL media
  • Some of each of the parent strains were also PCR tested to confirm the presence of the mCherry gene.
    • The PCR showed that the mCherry gene was indeed present.

    Week 5
  • ODs of the pAW50-mCherry and the 3 colonies of 12 that were grown in varying conditions were taken and they were all above OD=0.6.
  • The samples were prepared for overnight oxygen exposure as per the protocol.
  • The samples were taken to the plate reader to measure fluorescence.
    • Fluorescence was measured for all the 12 samples in each condition.
  • Since this pre-study gave us consistent, positive values for fluorescence, we were able to now refine the oxygen exposure protocol and apply it to characterization of our parts.
    • This detailed protocol can be found in our protocol section