Team:SJTU-BioX-Shanghai/Part3 TAL Improvement

From 2014.igem.org

Revision as of 03:24, 16 October 2014 by Kariny888 (Talk | contribs)

Why we want to improve it?

Whether the Freiburg's design is efficient or not

According to the experimental record of Freiburg, the success rate is higher than 95%(32/33). However, this result, to some degree, lacks statistical significance.

In the result section, they emphasize that there is a light band at 1200bp, which they believe could indicate that the Golden Gate connection works well. However, after conducting several experiments by ourselves, we find that the key point to indicate whether Golden Gate connection works is not the band at 1200bp. If the band is not clear and specific in the gel, it indicates the experiment doesn’t go well. We can easily find several light bands under the band of 1200bp. Moreover, the second light band is somewhat lighter than the band at 1200bp. Although the Freiburg can explain the results with the repeatability of the TALE sequence, we suppose that the possibility of the mismatch of the sticky ends still can’t be excluded. Frankly speaking, we try to believe that they really made it, but if the success cannot be repeated, there must be something wrong with their system. You can view Detail information in iGEM2012 Freiburg wiki.

The protocol we take to connect the parts of TALE

  1. Freiburg's protocol
  2. Restriction enzyme digestion of plasmid and TAL repeats and gel extraction respectively. By the mole ratio, plasmid to TALE is 1 to 5 and TALE to TALE is 1 to 1. Ligation with T4 ligase in 22 ℃over night.
  3. The same ratio of plasmid and TALE repeat, but add the TALE repeats one by one and ligation in 22 ℃, 30 minutes
  4. Every two parts connect at one time, and try to make three intermediates of 400bp, and then mix the plasmid to make the complete TALE.
  5. The same ratio and ligation with the program of 22℃ 2min, 40℃ 30,25 repeats.

The motivation to debug 2012 Freiburg’s parts

Unfortunately, all of our attempts failed. We didn’t manage to make a complete TALE, or even make two of them together. However, what is important for us is that when we try the 5th protocol, we notice an unexpected result. When we analyze the sequence result, we find that our left adaptor, 1st part and right adaptor connect together. Why do we get this result? We notice that their sticky end is TGAC, GCTC, and ACTC. That is to say, GCTC and ACTC connect with each other by mistake. In another word, if the sticky ends are very similar, they probably connect with each other. Although we failed again, the result gives us confidence to debug 2012 Freiburg's parts.

How do we connect certain monomer?

Some advanced tips for TALE protein

  1. Given a sample sequence with repeating amino acids:

    What XX means is that it determine the certain kind of base. For one unit of repetition, other amino acids can be identical.

  2. A fully functional TALE protein contains one sequence, that does not have repetitive units, recognizing base T, and similar sequence but is only half length as its end. That is, one complete TALE protein is able to recognize certain number of repetitive units and two bases.
  3. The length that can be recognized is not strictly twelve or fourteen. According to the published results, the length and certain sequence are dependent on number and type of monomer.

We can gather 96 bioparts based on Freiburg, and each part has its counterproductive base on certain location(1,2,3,4,5 or 6). By picking two bases on certain location, we are able to design one TALE protein sequence.


Previous Review: Freiburg’s way of connection

The main principles of connection is built upon the idea of Golden Gate Connection.( Sanjana, N. E. et al. A transcription activator-like effector toolbox for genome engineering. Nature Protocols 7, 171–192 (2012).)

The gust of these procedures is more related to one type of restriction enzyme, type II Restriction Enzyme, especially BsmBI enzyme.

The main feature of this enzyme is the recognition sequence is on only one side of cleavage site. It provides the way which can be used to get certain incision without damaging the whole sequence. The sticky end has 4bp base, and it could be designed even for combination of multiple sticky end. That feature is fancy at first, but we cannot regardless its latent shortcomings.

Let’s analyze the example (AA1) provided by Freiburg.

The underlined parts are recognized by BsmBI. Vertical bar(|) is the cutting position. As for this sample, TGAC is one sticky end which can combine with other seven sticky ends.